logoSouthwest Environmental Limited
Environmental Consultancy Services to Industry, Business and Individuals Email Us
London
02076 920 670
Exeter  
01392 927 961
Manchester 
01612 970 026 
Bristol 
01173 270 092 

Groundwater Contaminant Plume Travel-Time Calculator

When fuel spills, solvent leaks, or historical land contamination occur on a development site, regulators require a quantitative assessment of how rapidly dissolved contaminants will migrate towards Controlled Waters (rivers, boreholes, or aquifers). Use our free calculator below—based on Darcy's Law and the 1D Advection-Dispersion Equation—to estimate groundwater seepage velocity and contaminant plume breakthrough time.

1D Contaminant Plume Velocity & Travel-Time Estimator

Southwest Environmental Ltd
Advective Arrival (t50)
2.89 yrs
(1,056 days – Plume Center)
Early Breakthrough (tfront)
2.22 yrs
(812 days – Dispersive Edge)
Darcy Flux (q = K·i) 0.0375 m/day (13.7 m/yr)
Water Seepage Velocity (vs) 0.170 m/day (62.2 m/yr)
Retarded Plume Velocity (vc) 0.095 m/day (34.6 m/yr)
Hydraulic Conductivity (K) 2.89 × 10-5 m/s
Need a Phase 2 Investigation or Controlled Waters DQRA?
SWEL provides UK-wide Contaminated Land & Remediation Reports.
Contact SWEL
Method: 1D Darcy Seepage Velocity, Linear Sorption Retardation & Longitudinal Hydrodynamic Dispersion (αL = 0.1L). Preliminary screening only.

How to Calculate Groundwater Contaminant Plume Travel Time

In hydrogeology and contaminated land risk assessment, dissolved contaminants migrate through saturated soil and rock via two primary physical mechanisms listed in classical physics: Advection (bulk movement carried along by flowing groundwater) and Hydrodynamic Dispersion / Diffusion (spreading out of the plume due to pore-scale velocity variations and concentration gradients).

The Equations Behind the SWEL Calculator

Our screening calculator solves the 1D hydrogeological transport chain in four steps:

  1. Darcy Flux / Specific Discharge (q):
    q = K × i
    Where K is hydraulic conductivity (m/day) and i is the dimensionless hydraulic gradient (Δh/ΔL).
  2. Average Linear Groundwater Seepage Velocity (vs):
    vs = (K × i) / ne
    Because groundwater can only flow through the interconnected pore spaces rather than the solid mineral matrix, dividing Darcy flux by the effective porosity (ne) reveals the true porewater velocity—which is typically 3 to 10 times faster than the Darcy flux.
  3. Retarded Contaminant Velocity (vc):
    vc = vs / Rf  where  Rf = 1 + (ρb / ne) × Kd
    Hydrophobic organics (like petrol/diesel hydrocarbons and PAHs) and heavy metals temporarily bind (sorb) to soil organic carbon and clay surfaces, causing the contaminant plume to travel slower than the groundwater by a Retardation Factor (Rf).
  4. Advective Arrival vs Dispersive Leading-Edge Breakthrough:
    tadv = L / vc  (Center of Mass, 50% concentration arrival)
    Because longitudinal mechanical dispersion (αL ≈ 0.1L) causes the front edge of a plume to spread ahead of the center of mass, initial breakthrough (tfront) typically arrives ~23% earlier than pure plug-flow advection predicts.

Typical UK Aquifer Hydraulic Conductivity & Porosity Reference Table

During a Phase 2 Site Investigation, site-specific hydraulic conductivity (K) is measured via borehole rising/falling head slug tests or pumping tests. For initial desk-study screening, typical UK hydrogeological ranges are summarized below:

UK Geological Stratum / Aquifer Type Hydraulic Conductivity (K, m/day) Hydraulic Conductivity (K, m/s) Effective Porosity (ne)
River Terrace Gravels / Clean Coarse Sand 10 – 100+ m/day 10-4 – 10-3 m/s 0.20 – 0.30
Sherwood Sandstone / Medium Sand 1.0 – 10 m/day 10-5 – 10-4 m/s 0.15 – 0.25
Fractured Chalk / Karstic Limestone (Fissure Flow) 5.0 – 50+ m/day 5×10-5 – 5×10-4 m/s 0.01 – 0.05 (Fracture ne)
Silty Sand / Weathered Mudstone 0.05 – 1.0 m/day 5×10-7 – 10-5 m/s 0.10 – 0.18
Glacial Till / Unweathered Clay Aquitard 0.0001 – 0.01 m/day 10-9 – 10-7 m/s 0.03 – 0.08

Contaminated Land & Hydrogeology Consultants

Hopefully this tool helps you screen potential groundwater migration timescales on your site. If your site requires a formal Phase 1 Desk Study, Phase 2 Groundwater Monitoring, or Environment Agency Remedial Targets Methodology (RTM) modelling to discharge planning conditions, please call or email Southwest Environmental Limited.

Technical Requirements for Controlled Waters Risk Assessments (RTM / LCRM)

Under the Environment Agency's Land Contamination Risk Management (LCRM) framework, any site with a viable contaminant-pathway-receptor linkage to groundwater or surface water must undergo tiered assessment. While simple travel-time screening demonstrates how rapidly a plume can reach a receptor, regulatory sign-off frequently depends on natural attenuation and biodegradation during transit.

Why Travel Time Governs Biodegradation and Attenuation

In the Environment Agency's Tier 3 Remedial Targets Methodology (RTM), dissolved petroleum hydrocarbons (BTEX, MTBE, and TPH bands) and chlorinated solvents undergo microbial degradation as they travel through the aquifer. This exponential decay is governed by the half-life (t1/2) of the chemical and the plume travel time (t):

Understanding Dual-Porosity Chalk and Limestone Aquifers

Special care is required on UK Chalk and Jurassic Limestone Principal Aquifers. Although chalk has a high total matrix porosity (often > 30%), groundwater flow occurs predominantly through narrow interconnected fractures whose effective fracture porosity (ne) is tiny (often 0.01 to 0.03). Dividing Darcy flux by a 0.02 fracture porosity results in rapid linear seepage velocities—explaining why Environment Agency Source Protection Zones (SPZ1 50-day and SPZ2 400-day boundaries) extend far up-gradient in chalk catchments.